Neue Installation auf SP8

So, nun habe ich iodéOS wieder auf meinem Shiftphone. Der Installationsprozess war mal wieder nicht so einfach. Habe mal ein kleines Installationsprotokoll erstellt. Vielleicht können damit die Verantwortliche für die Installation ja etwas anfangen.

Hier das Protokoll - wollte ich eigentlich als PDF Hochladen:

Iodé Installation:

Nach dem Unlock des Bootloaders startet das Gerät normal, also nicht im Bootloader.

Habe es dann, wie in der Anleitung beschrieben, ausgeschaltet und mit drücken der Tasten

Power&Volume UP neu gestartet. Nach Erkennung des Systems durch den iodéOS-Installer auf

„Weiter“ geklickt.

Dann erscheint ein Fehler, jedenfalls geht es nicht mehr weiter. Nach knapp 10 Min Wartezeit, SP

neu im Bootloader gestartet.

Es scheint, als wenn die Installation normal weiter läuft. Dann erfolgt ein Neustart und ich bin wie-

der im alten Google-System. Daraufhin habe ich den IodéOS - Installer beendet.

Google grob eingerichtet. USB-debugging freigeschaltet und Installer neu gestartet. Im Installa-

tionsprozess, wie vorgesehen das Kabel wieder angeschlossen.

Bootloader korrekt entsperrt. System startet aber nicht im Bootloader.

Neustart ausgelöst, dann sofort die Tastenkombination Power&Volume UP gedrückt für den Boot-

loader-Start. Leider zeigt der Bildschirm Device State locked an. Google-System startet. Überprü-

fung, ob USB-Debugging noch eingeschaltet.

Installationvorgang abgebrochen und wieder neu gestartet. Installer neu gestartet. Am Menü-

punkt „Herunterladen der Konfiguration“ das Kabel wieder reingesteckt. Keine Reaktion des Instal-

lationsprogrammes. Nochmals gestartet, aber wieder nichts.

SP ausgeschaltet. Kabel ist angeschlossen. IodéOS-Installer neu gestartet. SP8 gestartet. Nichst

geht.

Kabel angeschlossen und Bootloader-Start erneut versucht. Diesmal ging es weiter, Bootloader

wurde entsperrt. Aber Gerät startete nicht im Bootloader. Deshalb ausgeschaltet, Neustart im

Bootloader-Modus. Weiter im Installer bis „System installieren“

. Sehe keinen Fehler. Warte-

zeit…ca. 10 Minuten, dann Abbruch der Installation.

SP8 ausgeschaltet.

Danach auf Manuelle Installation umgeschwenkt. Auch hier musste ich mehrfach starten, bis das

System installiert wurde.

Aber jetzt läuft es!!

--------------- Meldungen während des Installationsprozesses mit dem Installer----------------------------

Setting current slot to ‘a’ OKAY [ 0.006s]

Finished. Total time: 0.009s

Erasing 'avb

custom

_

_

key’ FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

Warning: skip copying avb

custom

_

_

key image avb footer (avb

custom

_

_

key partition size: 0, avb

custom

_

_

key image si-

ze: 1032).

Sending 'avb

custom

_

_

key’ (1 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

mke2fs 1.46.6 (1-Feb-2023)

Creating filesystem with 4096 4k blocks and 4096 inodes

Allocating group tables: 0/1 done

Writing inode tables: 0/1 done

Creating journal (1024 blocks): done

Writing superblocks and filesystem accounting information: 0/1 doneWarning: skip copying metadata image avb footer due to sparse image.

Sending ‘metadata’ (52 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

---------------------

Auf dem SP8 wurde derweil der Fastboot Mode Device State unlocked angezeigt

---------------------

Setting current slot to ‘a’ OKAY [ 0.006s]

Finished. Total time: 0.009s

Erasing 'avb

custom

_

_

key’ FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

Warning: skip copying avb

custom

_

_

key image avb footer (avb

custom

_

_

key partition size: 0, avb

custom

_

_

key image si-

ze: 1032).

Sending 'avb

custom

_

_

key’ (1 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

mke2fs 1.46.6 (1-Feb-2023)

Creating filesystem with 4096 4k blocks and 4096 inodes

Allocating group tables: 0/1 done

Writing inode tables: 0/1 done

Creating journal (1024 blocks): done

Writing superblocks and filesystem accounting information: 0/1 done

Warning: skip copying metadata image avb footer due to sparse image.

Sending ‘metadata’ (52 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

Sending 'modem

_

a’ (185916 KB) OKAY [ 3.971s]

Writing 'modem

_

a’ OKAY [ 0.382s]

Finished. Total time: 4.553s

--------------------------------------------

Bootloader Version…: 6.3

Baseband Version…:

Serial Number…: SP8002315002348

--------------------------------------------

extracting android-info.txt (0 MB) to RAM…

Checking ‘product’ OKAY [ 0.002s]

Setting current slot to ‘a’ FAILED (Status read failed (No such device))

fastboot: error: Command failed

< waiting for any device >

******** Did you mean to fastboot format this f2fs partition?

Erasing ‘userdata’ OKAY [ 0.790s]

Finished. Total time: 0.796s

Rebooting into fastboot FAILED (Status read failed (No such device))

fastboot: error: Command failed

< waiting for any device >

---------------------------

Neustart führt ins alte Google-System

---------------------------

Setting current slot to ‘a’ OKAY [ 0.006s]

Finished. Total time: 0.008s

Erasing 'avb

custom

_

_

key’ OKAY [ 0.008s]

Finished. Total time: 0.015s

Warning: skip copying avb

custom

_

_

key image avb footer (avb

custom

_

_

key partition size: 0, avb

custom

_

_

key image si-

ze: 1032).

Sending 'avb

custom

_

_

key’ (1 KB) OKAY [ 0.001s]Writing 'avb

custom

_

_

key’ fastboot: error: Command failed

< waiting for any device >

mke2fs 1.46.6 (1-Feb-2023)

Creating filesystem with 4096 4k blocks and 4096 inodes

FAILED (Status read failed (No such device))

Allocating group tables: 0/1 done

Writing inode tables: 0/1 done

Creating journal (1024 blocks): done

Writing superblocks and filesystem accounting information: 0/1 done

Warning: skip copying metadata image avb footer due to sparse image.

Sending ‘metadata’ (52 KB) OKAY [ 0.002s]

Writing ‘metadata’ OKAY [ 0.002s]

Finished. Total time: 0.029s

******** Did you mean to fastboot format this ext4 partition?

Erasing ‘metadata’ OKAY [ 0.017s]

Finished. Total time: 0.023s

< waiting for any device >

F2FS-tools: mkfs.f2fs Ver: 1.16.0 (2023-04-11)

Info: Debug level = 1

Info: Trim is disabled

Info: Set conf for android

Info: Enable Project quota

Info: not exist /proc/version!

Info: Segments per section = 1

Info: Sections per zone = 1

Info: sector size = 512

Info: total sectors = 929262232 (453741 MB)

Info: zone aligned segment0 blkaddr: 512

Info: add quota type = 0 => 4

Info: add quota type = 1 => 5

Info: add quota type = 2 => 6

Info: format version with

“6.14.0-123037-tuxedo”

[f2fs

init

sit

_

_

_

area: 714] Filling sit area at offset 0x00600000

[f2fs

init

nat

_

_

_

area: 748] Filling nat area at offset 0x02a00000

[f2fs

add

default

_

_

_

dentry_

root:1365] Writing default dentry root, at offset 0x47200

[f2fs

write

root

_

_

_

inode:1411] Writing root inode (hot node), offset 0x46c00

[f2fs

write

default

_

_

_quota:1503] Writing quota data, at offset 00047201 (1/2)

[f2fs

write

default

_

_

_quota:1503] Writing quota data, at offset 00047202 (2/2)

[f2fs

write

_

_qf

_

inode:1554] Writing quota inode (hot node), offset 0x46c01

[f2fs

write

default

_

_

_quota:1503] Writing quota data, at offset 00047203 (1/2)

[f2fs

write

default

_

_

_quota:1503] Writing quota data, at offset 00047204 (2/2)

[f2fs

write

_

_qf

_

inode:1554] Writing quota inode (hot node), offset 0x46c02

[f2fs

write

default

_

_

_quota:1503] Writing quota data, at offset 00047205 (1/2)

[f2fs

write

default

_

_

_quota:1503] Writing quota data, at offset 00047206 (2/2)

[f2fs

write

_

_qf

_

inode:1554] Writing quota inode (hot node), offset 0x46c03

[f2fs

_

update

nat

_

_

default:1592] Writing nat root, at offset 0x00002a00

Info: Overprovision ratio = 0.210%

Info: Overprovision segments = 489 (GC reserved = 483)

[f2fs

write

check

_

_

_point

_pack: 940] Writing main segments, cp at offset 0x00000200

[f2fs

write

check

_

_

_point

_pack:1028] Writing Segment summary for HOT/WARM/COLD

DATA, at offset

_

0x00000201

[f2fs

write

check

_

_

_point

_pack:1042] Writing Segment summary for HOT

NODE, at offset 0x00000202

_

[f2fs

write

check

_

_

_point

_pack:1054] Writing Segment summary for WARM

NODE, at offset 0x00000203

_

[f2fs

write

check

_

_

_point

_pack:1068] Writing Segment summary for COLD

NODE, at offset 0x00000204

_

[f2fs

write

check

_

_

_point

_pack:1076] Writing cp page2, at offset 0x00000205

[f2fs

write

check

_

_

_point

_pack:1118] Writing cp page 1 of checkpoint pack 2, at offset 0x00000400

[f2fs

write

check

_

_

_point

_pack:1137] Writing cp page 2 of checkpoint pack 2, at offset 0x00000405

[f2fs

write

_

_

super

_

block:1170] Writing super block, at offset 0x00000000Info: format successful

Warning: skip copying userdata image avb footer due to sparse image.

Sending ‘userdata’ (89 KB) OKAY [ 0.003s]

Writing ‘userdata’ OKAY [ 0.009s]

Finished. Total time: 0.589s

< waiting for any device >

Sending 'abl

_

a’ (172 KB) OKAY [ 0.004s]

Writing 'abl

_

a’ OKAY [ 0.006s]

Finished. Total time: 0.018s

Sending 'aop_

a’ (204 KB) OKAY [ 0.005s]

Writing 'aop_

a’ OKAY [ 0.006s]

Finished. Total time: 0.017s

Warning: skip copying bluetooth

_

a image avb footer (bluetooth

_

a partition size: 0, bluetooth

_

a image size: 520192).

Sending 'bluetooth

_

a’ (508 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

Sending 'cpucp_

a’ (184 KB) OKAY [ 0.005s]

Writing 'cpucp_

a’ OKAY [ 0.006s]

Finished. Total time: 0.018s

Warning: skip copying devcfg_

a image avb footer (devcfg_

a partition size: 0, devcfg_

a image size: 57344).

Sending 'devcfg_

a’ (56 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

Sending 'dsp_

a’ (65536 KB) OKAY [ 1.437s]

Writing 'dsp_

a’ OKAY [ 0.231s]

Finished. Total time: 1.676s

Warning: skip copying featenabler

_

a image avb footer (featenabler

_

a partition size: 0, featenabler

_

a image size:

90112).

Sending 'featenabler

_

a’ (88 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

Sending 'hyp_

a’ (3604 KB) FAILED (Write to device failed (No such device))

fastboot: error: Command failed

< waiting for any device >

Sending 'imagefv

_

a’ (524 KB) OKAY [ 0.014s]

Writing 'imagefv

_

a’ OKAY [ 0.009s]

Finished. Total time: 0.031s

< waiting for any device >

Sending 'keymaster

_

a’ (268 KB) OKAY [ 0.007s]

Writing 'keymaster

_

a’ OKAY [ 0.006s]

Finished. Total time: 0.020s

Sending 'multiimgoem

_

a’ (16 KB) OKAY [ 0.001s]

Writing 'multiimgoem

_

a’ OKAY [ 0.004s]

Finished. Total time: 0.010s

Sending 'qupfw

_

a’ (56 KB) OKAY [ 0.002s]

Writing 'qupfw

_

a’ OKAY [ 0.004s]

Finished. Total time: 0.012s

Sending 'qweslicstore

_

a’ (256 KB) OKAY [ 0.006s]

Writing 'qweslicstore

_

a’ OKAY [ 0.006s]

Finished. Total time: 0.018s

Sending 'shrm

_

a’ (48 KB) OKAY [ 0.001s]

Writing 'shrm

_

a’ OKAY [ 0.004s]

Finished. Total time: 0.011s

Sending 'tz

_

a’ (3720 KB) OKAY [ 0.083s]

Writing 'tz

_

a’ OKAY [ 0.026s]

Finished. Total time: 0.123s

Sending 'uefisecapp_

a’ (124 KB) OKAY [ 0.003s]

Writing 'uefisecapp_

a’ OKAY [ 0.004s]

Finished. Total time: 0.014s

Sending 'xbl

_

config_

a’ (224 KB) OKAY [ 0.005s]

Writing 'xbl

_

config_

a’ OKAY [ 0.008s]

Finished. Total time: 0.019sSending 'xbl

_

a’ (3600 KB) OKAY [ 0.081s]

Writing 'xbl

_

a’ OKAY [ 0.027s]

Finished. Total time: 0.120s

Rebooting into bootloader OKAY [ 0.000s]

Finished. Total time: 0.050s

OKAY [ 0.021s]

Finished. Total time: 0.021s

Du installierst unter Windows?

Ich sehe viele “Waiting for Device”. Ist USB stabil? Treiber OK, nachdem das Gerät erneut startet?

1 Like

Hallo Volker01, nein ich habe es unter Linux installiert. Inzwischen läuft es und ich habe mein kleines Protokoll nur beigelegt, damit die “Macher” der Installationsroutine ggf. noch Verbesserungen für neue User einbringen können.

Es sieht sehr nach USB-Kabel-/-Slotproblemen aus (waiting for any device). Das liegt dann wohl eher nicht an dem Installer, sondern an der Hardware deines Rechners oder deiner Kabel.

Hallo dwainzwerg, Kabel glaube ich eigentlich nicht. Es ist das Originalkabel von Shift mit dem ich schon verschiedene Datenübertragungen gemacht habe und letztlich auch das jetzt laufende System über meinen Linuxrechner (TuxedoOS) gemacht habe. Aber ausschließen kann ich es natürlich nicht. Und testen will ich es auch nicht mehr - bin froh, dass iodé läuft.
Schönen Wochenanfang